| 01-31-2004, 05:48 AM | #1 |
|
Junior Member
Join Date: Jan 2004
Posts: 16
|
just been having some trouble finding one
|
|
    |
| 01-31-2004, 11:31 AM | #2 |
|
Senior Member
Join Date: Jul 2003
Location: upstate ny
Posts: 1,555
|
For a 3 incher, you'll most likely have to talk to an exhaust shop and have it bent.
The place I was at could bend you up to a 4 and 1/2 in pipe if needed. Just check around. Good luck. Sam - |
|
|
|
| 01-31-2004, 02:25 PM | #3 |
|
Senior Member
Join Date: Jul 2003
Location: Fredericksburg, VA
Posts: 750
 |
Having your own made? Find and exaust shop with a mandrel bender.. Or one that will use 3 inch pipe and mandrel bends and piece it togather..
unless your looking for an aftermarket 80 mm exhaust.. i'll try and look around for one.
__________________
95 GSX600 89 Supra T http://img46.exs.cx/img46/4114/sleepywhitemk32.gif Cheap, fast, reliable, You can only pick two! |
|
|
|
| 01-31-2004, 04:08 PM | #4 |
|
Senior Member
Join Date: Aug 2003
Location: NOVA
Posts: 151
|
VIBRANT MAKES A GOOD 3 IN CATBACK LET ME KNOW IF YOU NEED A PRICE
|
|
|
|
| 01-31-2004, 06:02 PM | #5 |
|
Junior Member
Join Date: Jan 2004
Posts: 16
|
a price would definately be nice on the vibrant. im trying to avoid the muffler shop's and such since the quality of their work is often questionable. at my friends shop, someone actually had an exhaust made for a wrx legacy. the price was 300 dollars for materials and 20 hours of labor. at 65 dollars an hour for labor YOUCH. most of the muffler shops in this area only work with crush bent since it is so much easier and cheaper.
|
|
|
|
| 02-01-2004, 02:56 AM | #6 |
|
Senior Member
Join Date: Jul 2003
Location: MA
Posts: 1,518
  |
what kind of idiot would pay $1600 bucks for an exhaust thats not even tested and proven.
 |
|
|
|
| 02-02-2004, 05:23 PM | #7 |
|
Senior Member
Join Date: Jul 2003
Location: Lufkin, TX
Posts: 2,378
|
Thermal makes a 3" bolt on catback system... try them. Thermal's systems are very high quality.
|
|
|
|
| 03-01-2004, 06:18 AM | #8 |
|
Junior Member
Join Date: Mar 2004
Location: Burrillville, RI
Posts: 1
|
Does the Thermal unit have a 3" inlet flange or does it reduce it before the flange?
Kyle |
|
|
|
| 03-05-2004, 02:13 AM | #9 |
|
Junior Member
Join Date: Jul 2003
Location: Fort Worth, Texas
Posts: 21
|
have it made
|
|
|
|
| 01-28-2005, 11:33 PM | #10 |
|
Junior Member
Join Date: Jan 2005
Posts: 3
|
kteller.com
they have kits for lots of models, even swaps, then you only pay for welds. Jason |
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Well, Time For Me To Find A New Job... | 94solchick | Off-Topic | 3 | 03-15-2006 01:33 PM |
| How Did You Find Us? | simplegreen | Newbies! | 45 | 02-10-2006 08:22 PM |
| Find The Part | simplegreen | Civic | 4 | 02-16-2005 04:51 PM |
| Anyone know were i can find | Smooth_Imports | Off-Topic | 4 | 12-01-2003 03:59 AM |
| Where Could I Find A Set Of These? | imported_team_adrenaline | General Tech | 10 | 07-22-2003 04:10 PM |
Linear Mode
