Parts List So Far, Tell Me If I'm Missing Anything

[Smooth_Imports]

OK well i know i still need to order a head gasket and bearing but other then that and some gauges i think i'm almost done.

1. Eagle H-beam rods
2. Wiseco pistons
3. ACT HDSS clutch
4. 450cc injectors
5. Socketed OBD1 ECU with USB dataloggin
6. walbro 255 fuel pump
7. OBD conversion harness
8. moates chip burner
9. LT-1 wideband o2 sensor
10. ITR oil pump
11. ITR water pump
12. ITR timing belt
13. ARP head studs
14. Honda cam seal
15. Honda crank seal
16. Honda valve cover gakset
17. Honda spark well seals
18. honda VC grommets
19. Honda lower ball joint
20. HA-sport AC bracket
21. ARP rod bolts
22. 3 sets of NGK plugs for tuning
23. honda dizzy cap
24. honda dizzy rotor
25. NGK plug wires.
26. Greddy Type RS BOV


I think i might also order a new charge piping set, Beucase mine sucks. Other then that i'll i need is bull shit items. So now i'm just waiting for the parts to come rolling in. I have about 10% of what on the list already delivered.

[simplegreen]

kanibler pin.. missing 4 of those. i have em.. 800 each

[Smooth_Imports]

Originally posted by simplegreen@Nov 1 2005, 10:11 AM
kanibler pin.. missing 4 of those. i have em.. 800 each
<div align="right">[snapback]94844[/snapback]

[/quote]


Do you have muffler bearing too, I'm missing those as well

[cybergreenhatch]

how many psi you planning on running? just was wondering because i dunno if 450's will be big enough for what your looking for.

[dubcac]

I'd also go bigger on injectors...much better to have too much injector and have it not work as hard...and you have room to go up. Also, your rods will come with rod bolts...I might look into the importbuilders rods over Eagle if I were you. BTW, you forgot bearings and gaskets on your list.

http://www.importbuilders.com/rods.htm
He also sells Wiseco pistons there....the piston kits should come with rings. Check out his independant piston test, and you'll see why I like wiseco so much.

[Smooth_Imports]

Originally posted by dubcac@Nov 1 2005, 12:09 PM


I might look into the importbuilders rods over Eagle if I were you.* BTW, you forgot bearings and gaskets on your list.

<div align="right">[snapback]94861[/snapback]

[/quote]

I already order the rods, I knew they come with bolts but i had to pay extra for the ARP's. And i already ordered my pistons as well. Everything on thats list has been ordered and paid for. I could go with bigger injectors but i don't plan on maxxing these out, Well not until spring at least, so i would rather use the $200 on something else for the time being, i'm sure i'll go bigger down the line, but like i said i already paid for the 450's and they already shipped.

As for bearings, What do you guys think i should go with. I think i'm just going to order some Eagle H-pro series berings and have my maching shop match them up. I think that would be better then just going with the green hondas.

[dubcac]

The eagle rods should have come with ARP bolts...but anyways, I wouldn't run anything but OEM bearings.

[NstyGrnHatch]

Originally posted by dubcac@Nov 1 2005, 08:10 PM
The eagle rods should have come with ARP bolts...but anyways, I wouldn't run anything but OEM bearings.
<div align="right">[snapback]94920[/snapback]

[/quote]


mike go here for fuel injectore size cal.

http://www.smokemup.com/auto_math/fuel_injector.php

im assuming your gonna go for like 300-450hp? your gonna need like somwhere between 800-900cc injectors.

But on the headgasket note. Go to www.inlinepro.com. they have the best 3mm headgaskets on the market.

[cybergreenhatch]

720's should be sufficent

[Smooth_Imports]

i'm only looking for 300 whp max for now people, Maybe alittle more in the summer, I'm not looking for 1 gabillion horeseeeess.